該頁無縮略圖
SW-JD50/70/100/120A SW-JG50/70/100/120A
手持式激光測距儀
Laser Distance Meter
用戶手冊
User Manual
安全條例
初次使用儀器前，請先仔細閱讀安全條款和操作指南
在使用儀器之前請仔細閱讀本手冊中的所有操作指南和
安全條例，沒有按照本手冊所指引的操作方法使用儀器
有可能會造成儀器的損害、影響測量精度、對使用者或
第三者的人身傷害。
不要用任何方式自行打開或修理儀器，嚴禁非法改裝或
改變儀器激光發射器的性能。請妥善保管儀器，不要放
置在兒童可以接觸到的地方，避免無關人員的使用。
嚴禁用儀器激光器照射自已或他人的眼睛及身體其他部
位，嚴禁將激光器照射在高反光的物體表面上。
儀器電磁輻射可能對其他設備和裝置造成干擾，請不要
在飛機或醫療設備附近使用本儀器，不要在易燃、易爆
的環境中使用儀器。
儀器更換的廢舊電池和報廢的儀器不可與生活垃圾一同
處理，請按國家或者當?shù)氐南嚓P(guān)法律規定處理廢舊電池
和報廢儀器。
儀器出現任何的質量問題，或?qū)κ褂脙x器有任何疑問時
請及時聯系當?shù)亟?jīng)銷商或深達威科技廠家，我們將第一
時間為您解決。
- 01 -
顯示屏、按鍵
電量指示
角度指示
長度/面積/體積/
三角測量模式
激光發射指示
最大值指示
輔顯示區
數據存儲指示
最小值指示
主顯示區
顯示屏
按鍵
開機、測量鍵
面積/體積/
三角模式/聲音鍵
關機、清除鍵
測量基準/
單位選擇
累加/累減/
存儲鍵
- 02 -
關機狀態下，按 鍵，儀器和激光同時啟動，儀器
進入待測模式。
啟動儀器和關閉儀器
單位設定
長按 鍵，進入測量單位調整狀態，可重置當前測量
單位，本機默認的單位為：0.000m，該儀器提供了6種
單位可供選擇。
開機狀態下，長按 鍵3秒關閉儀器。150秒內未對
儀器進行任何操作，儀器將自動關閉。
安裝電池
電池保養
啟動儀器、功能設置
內置3.7V 600mAh 鋰電池供電，不可拆裝。儀器自
帶充電電路，具有明晰的欠壓指示、充電指示。
電池充電：請使用具有安全認證的DC 5V >1A充電器，
建議用手機充電器充電。
電池用過一段時間后容量不足時，開不了機或開機后，
電池符號空白閃爍顯示，需要及時充電。插入U(xiǎn)SB充
電，電池符號條形柱滾動顯示 ，充滿電后會顯
示 ，且閃爍。
長時間不使用時，先把產品充滿電，并每半年再充電一
次，以免電池放電損壞。
- 03 -
為保證儀器的精準度，提供了自助校準功能。
校準方法：在關機狀態下，持續按住 鍵，再按
鍵開機，松開 鍵，直到屏幕出現 下端有閃爍
的數字，進入自助校準模式。此時用戶可根據儀器的
誤差用 鍵對這個數值進行調整。
調整范圍為：-9~9mm。
短按 鍵進行設置前端基準和末端基準的相互轉換，
系統默認為末端基準。
本儀器背光燈為自動開和關。儀器在鍵入任一按鍵后，
背光燈會持續打開15秒，15秒后，儀器無操作將自動
關閉背光燈，以節省電源。
長按 鍵可開啟或關閉語音播報功能。
測量單位：
測量基準設置
背光燈開啟/關閉
聲音開啟/關閉
自助校準功能
長 度 面 積 體 積
1
6
5
4
3
2
0.000 m
0.00 ft
0'00\" 1/16
0 1/16 in
0.0 in
0.00 m
0.000 m2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 m2
0.000 m3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 m3
- 04 -
待測模式下長按 鍵，進入連續測量狀態，屏幕上輔
助顯示區會顯示此次連續測量過程中的最大測量值和最
小值。
主顯示區會顯示當前測量值，短按 鍵或 鍵退出
連續測量模式。
若本機測量值為3.783m，比實際值大3mm，則可進入
校準模式，用 鍵將校準值在現有基礎上下調3mm。
調整完畢后，按 鍵保存校準結果。
例如：實際距離為3.780m
若本機測量值為3.778m，比實際值小2mm，則可進入
校準模式，用 鍵將校準值在現有基礎上上調2mm。
待測模式下短按 鍵，儀器激光發射，鎖定測量點。
再按 鍵進行單次距離數據的測量，測量結果顯示
在主顯示區。
單次測量
連續測量
- 05 -
按 鍵二次，系統進入體積測量狀態，儀器進入體積
狀態，屏幕上會有一個立方體閃爍 ，根據提示完成
下列操作:
按 鍵進行第一條邊的測量（長）
按 鍵進行第二條邊的測量（寬）
按 鍵進行第三條邊的測量（高）
在測量過程中，還可以短按 鍵清除本次測量結果重
新測量。
按 鍵，退出體積測量狀態，進入長度測量模式。
儀器會自動進行體積運算，結果顯示在主顯示區。
輔助顯示區顯示立方體的長寬高的測量值。
按 鍵，退出面積測量狀態，進入長度測量模式。
按 鍵一次，屏幕會顯示 ，長方形一條邊閃爍。
根據提示完成下列操作:
按 鍵進行第一條邊的測量（長）
按 鍵進行第二條邊的測量（寬）
儀器會自動進行面積運算，結果顯示在主顯示區。
輔助顯示區顯示長方形的長和寬的測量值。
在測量過程中，還可以短按 鍵清除本次測量結果重
新測量。
面積測量
體積測量
- 06 -
勾股定理間接測量
儀器預設有四種利用勾股定理測量三角形單邊距離模式，
方便用戶在特定復雜環境下進行間接測量。
h
短按 鍵四次，屏幕顯示: ，三角形的斜邊閃爍
按 鍵依屏幕提示先測出虛線直角邊斜邊的長度(a)
同時測出斜邊與底邊夾角 。
儀器自動計算水平距離b與垂直高度h。
測角測高
短按 鍵六次，屏幕顯示: ，三角形的斜邊閃爍
按 鍵依屏幕提示先測出一條虛線斜邊的長度(a)
按 鍵測出中間一條虛線斜邊的長度(b)
按 鍵測出另一條虛線底邊的長度(c)
儀器自動計算出實線三角形一條邊的長度(x）
測量三角形三條虛線邊，間接測量三角形一條邊的長度
短按 鍵五次，屏幕顯示: ，三角形的直角邊
閃爍
按 鍵依屏幕提示測出一條虛線直角邊的長度(a)
按 鍵測出另一條虛線直角邊的長度(b)
儀器自動計算實線斜邊的長度(x)
測量三角形兩直角邊，間接測量斜邊長度
- 07 -
單段距離測量可通過加/減運算進行累加或累減操作。
用戶在測量單段距離得到一次測量結果后，再通過
鍵進入累加累減功能選擇，短按 鍵，當屏幕測量主
顯示區出現“+”，進入累加測量模式，屏幕顯示上次測
量值與當次測量值的累加值。
短按 鍵，當屏幕測量主顯示區出現“-”，進入累減
測量模式，屏幕顯示上次測量值與當次測量值的差值。
不僅距離可累加累減，面積和體積也可進行累加累減。
下面舉例說明面積的累加累減功能，體積的累加累減與
此類似。
加減測量功能
短按 鍵七次，屏幕顯示: ，三角形的斜邊閃爍
按 鍵依屏幕提示測出一條虛線斜邊的長度(a)
按 鍵測出如圖虛線邊的長度(b)
按 鍵測出如圖另一條虛線斜邊的長度(c)
儀器自動計算出實線直角邊的長度(x）
測量三角形三條虛線邊，間接測量直角邊長度
勾股測量模式下，直角邊必須小于斜邊長度儀器才能計算，
否則儀器會顯示錯誤信號提示。在勾股測量模式下，為保
證測量的精度，須確保從同一個起始點測量，并按斜邊、
直角邊測量順序測量。
- 08 -
面積累加：測量第一個面積，得到結果如下圖1所示。
然后按下 鍵，再測量第二個面積，得到結果如下
圖2所示，在左下角會顯示一個加號。最后，按下
鍵得到兩次面積求和的結果，結果如圖3所示。
長按 鍵，查詢已儲存的測量數據，短按 鍵向后
翻記錄，短按 向前翻記錄。在查看記錄過程中，長
按 鍵清除所有記錄。可短按 鍵或 鍵退出該
狀態。
圖1 圖2 圖3
測量模式下，當前數據有效時，儀器將自動存儲到內存
中，屏幕頂部記錄號 不斷累加。
測量記錄存儲功能
顯示屏上方時刻顯示有角度信息，角度的測量范圍是
-90°～90°。
角度測量
瀏覽/刪除記錄：
- 09 -
使用過程中，主顯示區可能會出現如下提示信息：
提示信息
信息
Err 超出距離測量范圍
Err 1 信號過弱
Err 2 信號過強
Err 3 電池電壓過低
Err 4 超出工作溫度范圍
Err 5 勾股測量違規
讓儀器在量程范圍內使用
測量反射能力強的目標點
測量反射能力弱的目標點
對電池進行充電
讓儀器在指定環境中使用
重新測量，確保斜邊大于直角邊
原因 解決方法
- 10 -
技術參數
±(2mm+d×1/10000) 室內標準反射面**
-10℃~50℃
-20℃~60℃
630-670nm，<1mW 500-800nm，<1mW
SW-JD50/70/100/120A SW-JG50/70/100/120A
0.05-50m/70m/105m/125m
項目
≥8000次（單次測量）
150秒
20秒 (單次測量)
99筆
3.7V 600mAh 鋰電池
20%~80%RH
108x50x25mm
自動切斷激光
測量距離范圍
距離測量精度
勾股測量功能
最大/最小值
自助校準功能
加減測量功能
面積/體積加減
語音播報
存儲記錄筆數
激光等級
激光類型
存儲溫度范圍
工作溫度范圍
電池工作時間
連續測量功能
面積體積測量
自動關機
電池規格
存儲濕度
外形尺寸
±1°
傾角測量范圍 ±90?
角度精度
充電規格 Type-C DC 5V 0.5A
2級
- 11 -
* “d”表示實際距離。
** 在惡劣的環境下，如陽光過于強烈、環境溫度波動過大、反
射面反射效果較弱、電池電量不足等情況，測量結果會有較大
的誤差，此種情況配合目標反射板測量效果更佳。
禁止將儀器長期放置在高溫高濕的環境中儲存，長期
不使用儀器時，請取出電池并把儀器放置在隨機的儀
器套內放在陰涼干爽處存放。
請保持儀器表面清潔，可用濕的軟布擦拭表面灰塵，
不可用帶有腐蝕性洗液清潔儀器?？砂凑詹潦霉鈱W(xué)器
件表的方法擦拭激光器窗口和聚焦鏡。
購買儀器時請按下列清單認真檢查儀器所有附件是否
完整?
檢驗員： 日期：
儀器日常保養
裝箱清單
項目
1 主機 臺 1
名稱 單位 數量 備注
2 鋰電池 塊 1 內置不可拆
3 說明書 本 1
4 保修合格證 張 1
5 彩盒 個 1
6 掛繩 條 1
- 12 -
Safety Regulations
Please read the safety regulations and operation
guide carefully before operating.
Please read all of the operational guide and safety regulations in this manual before operation . Improper operations without complying with this manual may cause
damage to the device, influence on measurement result
or cause personal injury to the user or a third party.
The instrument is not allowed to disassemble or repair in
any ways. It is forbidden to do any illegal modification or
performance change for the laser emitter. Please keep it
out of reach of children and avoid being used by any
irrelevant person.
It is strictly prohibited to shoot eyes or other parts of
body with the laser. It is not allowed to take the laser to
shoot the surface of any highly reflective objects.
Due to electromagnetic radiation interference to other
equipment and devices, please don't use the meter in
the plane or around medical equipment, don’t use it in
inflammable, explosive environment.
Discarded batteries or meter device should not be processed just like household garbage, please handle them in
line with related law and regulations.
Any quality issues or any questions on the meter, please
contact local distributors or manufacturer in time, we are
ready to offer solutions for you.
- 13 -
Display/Button
Power Supply
Length, Area, Volume
and Pythagorean
Laser on
Maximum Value
Auxiliary Display
Record
Minimum Value
Major Display
Display
Button
Turn on/Measuring
Sound/Area/Volume/
Pythagorean Mode
Turn off/Remove
Reference Point/
Unit Switch
Addition &
Subtration/Save
- 14 -
Under off state, press , device and laser get
started simultaneously and the device enters the
measurement mode.
Under on state, long press for 3 seconds to turn
the device off. The device can also be shut off without
any operation within 150 seconds.
The built-in 3.7V 600mAh lithium battery is
non-removable. The instrument has its own charging
circuit, with clear undervoltage indication and
charging indication.
Battery charging: Please use a DC 5V >1A charger
with safety certification. A mobile phone charger is
recommended.
The instrument shall be charged in time when
running out of battery or its battery symbol shows
blank and flashes due to insufficient battery capacity.
Insert USB to charge, and the battery symbol scrolls
to display . When fully charged, will display
and flash.
Turn On/Off the Instrument
Long press , reset current measurement unit, the
default unit is: 0.000m. There are 6 units for selection.
Unit Setting
Batteries Installation
Start the Instrument/Menu Setting
- 15 -
Long press to toggle voice broadcast function.
Short press to change the reference point.
The default reference point is the terminal baseline.
The backlight is set to turn on and off automatically.
The backlight will be on for 15 seconds if any key is
pressed. The backlight will automatically turn off if
there is no operation within 15 seconds to save power.
Measurement units:
Changing Reference Point
Backlight on/off
Keys Sound
Length Area Volume
1
6
5
4
3
2
0.000 m
0.00 ft
0'00\" 1/16
0 1/16 in
0.0 in
0.00 m
0.000 m2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 m2
0.000 m3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 m3
- 16 -
The adjustment range is -9~9mm. Finally, long press
to save the setting.
First, make sure the device is power off, long press
then press to start the device. Next, loose when
\"CAL\" and a twinkling figure show at the display. Then
the device enters self-calibration mode. At this time,
the user can adjust the figure by and according
to the error of the instrument.
Under the test mode, press , and the instrument
emits laser to lock the measuring point. Press
again for single distance measurement, and the
measurement result will be displayed in the major
display area.
Self-calibration function is provided to ensure the
precision of the device.
After the adjustment, press to save the calibration
result.
For example, the actual distance is 3.780m.
If the measured value is 3.778m, 2mm smaller than
the actual value, the calibration value can be adjusted
up by 2mm on the existing basis with through the
calibration function.
If the measured value is 3.783m, 3mm larger than the
actual value, the calibration value can be lowered by
3mm on the existing basis with through the
calibration function.
Self-Calibration
Single Measurement
- 17 -
Press again to exit the mode.
Press , clear off the result and measure again if
necessary.
Press once for length
Press again for width
The current measurement value will display in the
main display area. Short press or to exit the
continuous measurement mode.
Under the test mode, long press to enter the
continuous measurement mode, and the maximum
and minimum measured values measured in the
continuous measurement process will display in the
auxiliary display area.
Press , shows at the screen. One of the side
of rectangle blinks at the display, please follow the
below instructions for area measurement:
The device automatically calculates the area and
shows the result in the major display area. The
measuring results of the length and width of the
rectangle will be showed in the auxiliary display area.
Continuous Measurement
Area Measurement
- 18 -
The device automatically calculates the volume and
shows the result in the major display area. The
measuring results of the length, width and height of
the cube will be showed in the auxiliary display area.
Press for length
Press again for width
Press thirdly for height
Press , clear off the result and measure again if
necessary.
Press again to exit the mode.
Press twice to enter volume measurement mode.
A will show at the top of the screen. Please follow
the below instruction for volume measurement:
Volume Measurement
Pythagoras
h
There are four modes of measuring the triangular
unilateral distance by means of Pythagorean theorem,
which are convenient for users to measure indirectly
in specific complex environments.
- 19 -
Short press four times, shows on the
screen, and the hypotenuse of the triangle flashes
Press according to the screen prompt first
measure the length of the hypotenuse of the right
Angle of the dotted line (a) and measure the Angle
between the hypotenuse and the bottom edge.
The device automatically calculates the horizontal
distance (b) and vertical height (h) .
Angle and Height Measurement.
Short press five times, shows on the
screen, the right side of the triangle flashes
Press to measure the length of the right Angle
of a dotted line according to the screen prompt (a).
Press to measure the length of the right side of
the other dotted line (b).
The device automatically calculates the length of
hypotenuse (x).
Calculate the hypotenuse by measuring the length
of two sides.
Measure the three dotted edges of the triangle, and
indirectly measure the length of one side of the
triangle.
Press six times, shows on the screen, the
hypotenuse of the triangle flashes
Press to measure the length of the hypotenuse
of a dotted line (a).
Press to measure the length of the hypotenuse
of a dotted line in the middle (b).
Press to measure the length of the bottom of
the other dotted line (c).
- 20 -
The device can be used for the addition and subtraction of single measurement distance. After obtaining
the result of a single measurement, enter the selection
of addition/subtraction function through .
Addition/Subtraction
In the Pythagorean Measurement Mode, the right
Angle side must be less than the hypotenuse length of
the instrument to calculate, otherwise the instrument
will display an error signal prompt. In the Pythagorean
Measurement Mode, to ensure the accuracy of the
measurement, it is necessary to ensure that the
measurement is taken from the same starting point
and in the order of the hypotenuse and right Angle
side measurements.
The device automatically calculates the length of
one side of the solid triangle (x).
Press seven times, shows on the screen,
the hypotenuse of the triangle flashes
Press to measure the length of the hypotenuse
of a dotted line (a).
Press to measure the length of the dotted line
as shown (b).
Press to measure the length of the hypotenuse
of the other dotted line in the picture (c).
The device automatically calculates the length of
the right Angle side of the solid line (x).
Measure the three dotted edges of the triangle,
and indirectly measure the length of one side of the
triangle.
- 21 -
In measurement mode, if the current data is valid, it
will be automatically stored in memory, and the record
number at the top of the screen will continue to
accumulate.
Record Function
Short press , when \"-\" shows in the major display
area, the device enters subtraction mode. The screen
displays the difference between the last measured
value and the current measured value.
Measure the first area and the result is shown in PIC1.
Then press to measure the second area and the
result is shown in PIC2, and \"+\" will appear in the
lower left corner of the screen. Finally, press to get
the sum of two areas, as shown in PIC3.
Not only length can be caculated by addition and
subtraction, but also area and volume. Take area as
an example:
Short press , when \"+\" shows in the major display
area, the device enters addition mode. The screen
displays the sum of the last measured value and the
current measured value.
PIC1 PIC2 PIC3
- 22 -
During use, the following prompts may be displayed
in the major display area:
The angle information is displayed at the top of the
screen, and the angle measurement range is -90.0°
to 90.0° .
Err 1
Err
Err 2
Err 3
Err 4
Err 5
Prompt Cause Solution
Signal is too weak
Out of the
measurement range
Use the device within the
measurement range.
Choose the surface with stronger
reflection. Use the reflecting plate.
Signal is too strong Choose the surface with weaker
reflection.
Low battery voltage Charging the battery.
Beyond working
temperature
Pythagoras measuring
breaks the rules
Re-measure and ensure that
hypotenuse is longer than legs.
Use the device in the specified
temperature.
Long press to browse the stored measurement
data, use to scroll backward for record, use to
scroll forward for record. While browsing records, long
press to clear all records. Short press or to
exit the mode.
Browse/Delete the Records
Tips
Angle Measurement
- 23 -
Technology Specifications
± (2mm+d×1/10000)
Indoor standard reflective surfaces **
-10°C~50°C
-20°C~60°C
630-670nm, <1mW 500-800nm, <1mW
SW-JD50/70/100/120A SW-JG50/70/100/120A
0.05-50m/70m/105m/125m
ITEM
≥8000 times (single measurement)
150s
20s (single measurement)
99 units
3.7V 600mAh Li-ion
20%~80%RH
108x50x25mm
Automatically Cut
off Laser
Measuring Range
Measuring Accuracy
Pythagorean
Measurement
Min/Max Value
Self-Calibration
Add and Subtract
Measurement
Area&Volume
Addition/Subtraction
Voice Broadcast
Max Storage
Laser Level
Laser Type
Storage Temperature
Working Temperature
Operating Time
Continuous
Measurement
Area/Volume
Measurement
Auto Power-off
Battery
Storage Humidity
Dimension
Type-C DC 5V 0.5A
±90?
Angle Accuracy ±1°
Angle Range
Charging Specification
II
- 24 -
* \"d\" indicates the actual distance.
** In harsh environments, such as strong sunlight, large
fluctuations in ambient temperature, the reflecting surface with
weak reflection effect, and low battery, there will be a large
error in the measurement results. In this case, to enhance the
measurement effect, please use the target reflector.
The meter should not be stored in high temperature
and humid environment for a long time. If it is not
used very often, please take out the battery and
place the meter in the portable bag and store it in
cool and dry place.
Please keep the device surface clean. Use a soft
wet cloth to wipe the dust on the surface. Do not use
corrosive liquid to clean the device. Use the same
method as wiping optical devices to wipe the meter
and focusing mirror.
User Manual
Meter 1
1
1
3
4
pc
No. Item Unit QTY Note
pc
Lithium Battery Built-in and
non-removable 2 pc 1
Gift Box pc 1
5 Hand Strap pc 1
Please check if all accessories are complete according
to the following list.
Instrument Maintenance
Packing List
- 25 -
深達威科技（廣東）股份有限公司
地址：廣東省東莞市虎門鎮虎門團結路58號
Sndway Technology (Guangdong) Co., LTD.
Add: No.58, Humen Tuanjie Road, Humen Town
Dongguan City, Guangdong Province, China
全國咨詢服務熱線 /Service Hotline: 400-125-6969
電話/Tel: 0769-85265688
網址/Web: www.sndway.com
郵箱/E-mail: market@sndway.com
