該頁無縮略圖
手持式激光測距儀
User Manual
用戶手冊
SW-M70S SW-M100S SW-M120S
安全條例
初次使用儀器前，請先仔細閱讀安全條款和操作指南
在使用儀器之前請仔細閱讀本手冊中的所有操作指南和安
全條例，沒有按照本手冊所指引的操作方法使用儀器有可
能會造成儀器的損害、影響測量精度、對使用者或第三者
的人身傷害。
不要用任何方式自行打開或修理儀器，嚴禁非法改裝或改
變儀器激光發射器的性能。請妥善保管儀器，不要放置在
兒童可以接觸到的地方，避免無關人員的使用。
嚴禁用儀器激光器照射自已或他人的眼睛及身體其他部位，
嚴禁將激光器照射在高反光的物體表面上。
儀器電磁輻射可能對其他設備和裝置造成干擾，請不要在
飛機或醫療設備附近使用本儀器，不要在易燃、易爆的環
境中使用儀器。
儀器更換的廢舊電池和報廢的儀器不可與生活垃圾一同處
理，請按國家或者當?shù)氐南嚓P(guān)法律規定處理廢舊電池和報
廢儀器。
儀器出現任何的質量問題，或?qū)κ褂脙x器有任何疑問時請
及時聯系當?shù)亟?jīng)銷商或深達威科技廠家，我們將第一時間
為您解決。
2016L197-44
- 01 -
顯示屏、按鍵
按鍵
存儲鍵/
加/減鍵
開機/測量鍵
聲音開關/
模式鍵
關機/清除鍵
測量基準/
單位選擇鍵
電量指示
面積/體積/
三角測量模式
激光發射指示
最大值指示
輔顯示區
數據存儲指示
最小值指示
主顯示區
顯示屏
長度測量模式
- 02 -
打開儀器背部的電池門，按照極性指示正確放入電池，
并關閉電池門。
儀器只能使用1.5V AAA的堿性電池。
長時間不使用儀器時，請取出電池，以避免電池腐蝕
儀器主機。
安裝更換電池
啟動儀器和關閉儀器
單位設定
安裝電池
啟動儀器、功能設置
關機狀態下，按 鍵，儀器啟動，儀器進入待測模
式。
長按 鍵，進入測量單位調整狀態，可重置當前測
量單位，本機默認的單位為：0.000m，該儀器提供了
6種單位可供選擇。
開機狀態下，長按 鍵3秒關閉儀器。150秒內未對
儀器進行任何操作，儀器將自動關閉。
- 03 -
本儀器背光燈為自動開和關。儀器在鍵入任一按鍵后，
背光燈會持續打開15秒，15秒后，儀器無任何操作將
自動關閉背光燈，以節省電源。
短按 鍵進行設置前端基準和末端基準的相互轉換，
系統默認為末端基準。
測量基準設置
背光燈開啟/關閉
長按 鍵可關閉或打開聲音控制。
聲音開啟/關閉
測量單位：
長 度 面 積 體 積
1
6
5
4
3
2
0.000 m
0.00 ft
0'00\" 1/16
0 1/16 in
0.0 in
0.00 m
0.000 m2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 m2
0.000 m3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 m3
- 04 -
自助校準功能
此時用戶可根據儀器的誤差用 鍵對這個數值進行
調整。調整范圍為-9～9mm。
例如：實際距離為3.780m
若本機測量值為3.778m，比實際值小2mm，則可進入
校準模式，用 鍵將校準值在現有基礎上上調2mm。
若本機測量值為3.783m，比實際值大3mm，則可進入
校準模式，用 鍵將校準值在現有基礎上下調3mm。
調整完畢后，按 鍵保存校準結果。
為保證儀器的精準度，提供了自助校準功能。
校準方法：在關機狀態下，持續按住 鍵，再按
鍵開機，松開 鍵，直到屏幕出現 ，下端有閃
爍的數字，進入自助校準模式。
單次測量
待測模式下短按 鍵，儀器激光發射，鎖定測量點。
再按 鍵進行單次距離數據的測量，測量結果顯示在
主顯示區。
連續測量
待測模式下長按 鍵，進入連續測量狀態，屏幕上輔
助顯示區會顯示此次連續測量過程中的最大測量值和最
小值。
主顯示區會顯示當前測量值，短按 鍵或 鍵退出
連續測量模式。
- 05 -
面積測量
按 鍵一次，屏幕會顯示 ，長方形一條邊閃爍。
根據提示完成下列操作:
儀器會自動進行面積運算，結果顯示在主顯示區。輔助
顯示區顯示長方形的長和寬的測量值。
在測量過程中，還可以鍵入 清除本次測量結果重新
測量。連續按 鍵兩次，退出面積測量狀態，進入長
度測量模式。
按 鍵進行第一條邊的測量（長）
按 鍵進行第二條邊的測量（寬）
體積測量
按 鍵二次，屏幕會顯示 ，立方體一條邊閃爍，
根據提示完成下列操作:
儀器會自動進行體積運算，結果顯示在主顯示區。輔助
顯示區顯示立方體長寬高的測量值。
按 鍵進行第一條邊的測量（長）
按 鍵進行第二條邊的測量（寬）
按 鍵進行第三條邊的測量（高）
在測量過程中，還可以鍵入 清除本次測量結果重新
測量。連續按 鍵兩次，退出體積測量狀態，進入長
度測量模式。
- 06 -
勾股定理間接測量
按 鍵依屏幕提示先測出虛線斜邊的長度 (a)
按 鍵測出虛線直角邊(底邊)的長度 (b)
儀器預設有四種利用勾股定理測量三角形單邊距離模式，
方便用戶在特定復雜環境下進行間接測量。
短按 鍵三次，屏幕顯示: ，三角形的斜邊閃爍
儀器自動計算實線直角邊(高)的長度 (x)
測斜邊和底，間接測量高度
按 鍵依屏幕提示先測出虛線直角邊的長度 (a)
按 鍵測出另一條虛線直角邊的長度 (b)
短按 鍵四次，屏幕顯示: ，三角形的直角邊閃
爍
儀器自動計算實線斜邊的長度 (x)
測量直角三角形兩直角邊，間接測量斜邊長度
- 07 -
按 鍵依屏幕提示先測出虛線斜邊的長度 (a)
按 鍵測出中間一條虛線斜邊的長度 (b)
按 鍵測出另一條虛線直角邊的長度 (c)
短按 鍵五次，屏幕顯示: ，三角形的直角邊閃
爍
儀器自動計算出實線三角形一條邊的長度 (x)
測兩條斜邊和底邊，間接測量輔助高度
按 鍵依屏幕提示先測出虛線斜邊的長度 (a)
按 鍵測出中間一條虛線斜邊的長度 (b)
按 鍵測出另一條虛線斜邊的長度 (c)
短按 鍵六次，屏幕顯示: ，三角形的斜邊閃爍
儀器自動計算出實線三角形一條邊的長度 (x)
測兩斜邊和高，間接測量底邊和
勾股測量模式，直角邊必須小于斜邊長度儀器才能計算，
否則儀器會顯示錯誤信號提示。在勾股測量模式下，為
保證測量的精度，須確保從同一個起始點測量，并按斜
邊、直角邊測量順序測量。
勾股測量模式下，直角邊必須小于斜邊長度儀器才能
計算，否則儀器會顯示錯誤信號提示。在勾股測量模
式下，為保證測量的精度，須確保從同一個起始點測
量，并按斜邊、直角邊測量順序測量。
- 08 -
面積累加：
1. 測量第一個面積，得到結果如下圖1所示。
2. 短按 鍵，進入累加模式，再測量第二個面積，得
到結果如下圖2
3. 短按 鍵，得到兩次面積求和的結果，結果如圖3
所示。
圖1 圖2 圖3
加減測量功能
單段距離測量可通過加/減運算進行累加或累減操作。
用戶在測量單段距離得到一次測量結果后，再通過
鍵進入累加累減功能選擇，短按 鍵，當屏幕出現
“+”，進入累加測量模式，屏幕顯示上次測量值與當次
測量值的累加值。
再次短按 鍵，當屏幕出現“-”，進入累減測量模式，
屏幕顯示上次測量值與當次測量值的差值。
累加累減模式通過 鍵循環選擇
不僅距離可累加累減，面積和體積也可進行累加累減。
下面舉例說明面積的累加累減功能，體積的累加累減與
此類似。
- 09 -
長按 鍵，查詢已儲存的測量數據，用 鍵向后翻記錄，
用 鍵向前翻記錄。在查看記錄過程中，長按 鍵清除
所有記錄?？啥贪?鍵或 鍵退出該狀態。
多次面積累加：
在面積累加第2步操作之后，繼續短按 鍵，可再次累
加下一個面積，重復該步驟，可進行多次累加，最后執
行第3步求和。
面積累減：
在面積累加第1步之后，重復短按 鍵，可切換累加累
減模式，但第二次面積開始測量后，不可再切換累加減，
只能繼續累加/累減。
累減及多次累減操作和累加類似，請用戶參考累加操作。
測量記錄存儲功能
測量模式下，當前數據有效時，儀器將自動存儲到內存
中，屏幕頂部記錄號“ ” 不斷累加。
瀏覽/刪除記錄：
- 10 -
提示信息
使用過程中，主顯示區可能會出現如下提示信息：
更換電池
讓儀器在指定環境中使用
測量反射能力弱的目標點
測量反射能力強的目標點
重新測量，確保斜邊大于直角邊
讓儀器在量程范圍內使用
信息
Err 超出距離測量范圍
Err 1 信號過弱
Err 2 信號過強
Err 3 電池電壓過低
Err 4 超出工作溫度范圍
Err 5 勾股測量違規
原因 解決辦法
- 11 -
±(2mm+dx1/10000)室內標準反射面**
按鍵提示音
20秒 (單次測量)
99筆
630-670nm，<1mW
SW-M70S SW-M100S SW-M120S
0.05-70m 0.05-105m 0.05-125m
項目
測量距離范圍
距離測量精度
連續測量功能
勾股測量功能
加減測量功能
面積/體積加減
最大/最小值
自助校準功能
激光等級
激光類型
存儲記錄筆數
自動切斷激光
電池規格 2x1.5V AAA
面積/體積測量
滿電測量次數 ≥8000次 (單次測量)
工作溫度 0°C~40°C
存儲溫度 -20°C-60°C
存儲濕度 20%-80%RH
外形尺寸 100x43x23mm
自動關機 150秒
Class II
技術參數
- 12 -
* “d”表示實際距離
** 在惡劣的環境下，如陽光過于強烈、環境溫度波動過大、反射
面反射效果較弱、電池電量不足等情況，測量結果會有較大的誤
差，此種情況配合目標反射板測量效果更佳。
儀器日常保養
裝箱清單
禁止將儀器長期放置在高溫高濕的環境中儲存，長期
不使用儀器時，請把儀器放置在隨機的儀器套內放在
陰涼干爽處存放。
請保持儀器表面清潔，可用濕的軟布擦拭表面灰塵，
不可用帶有腐蝕性洗液清潔儀器。可按照擦拭光學器
件表面的方法擦拭激光器窗口和聚焦鏡。
項目
1 主機 臺 1
2 1.5V AAA電池 節 2
名稱 單位 數量 備注
1
1
1
1
3 掛繩 條
4 說明書 本
5 彩盒 個
6 保修合格證 張
購買儀器時請按下列清單認真檢查儀器所有附件是否完
整。
- 13 -
Safety Regulations
Please read the safety regulations and operation guide
carefully before operating.
Please read all of the operational guide and safety regulations
in this manual before operation. Improper operations without
complying with this manual may cause damage to the device,
influence on measurement result or cause personal injury to
the user or a third party.
The instrument is not allowed to disassemble or repair in any
ways. It is forbidden to do any illegal modification or performance change for laser emitter. Please keep it out of reach
of children and avoid being used by any irrelevant person.
It is strictly prohibited to shoot eyes or other parts of body
with the laser. It is not allowed to take the laser to shoot the
surface of any highly reflective objects.
Due to electromagnetic radiation interference to other
equipment and devices, please don't use the meter in the
plane or around medical equipment, don’t use it in
inflammable or explosive environment.
Discarded meter device should not be processed just like
household garbage, please handle it in line with related law
and regulations.
If there are any quality problems with the instrument or any
questions about the use of the instrument, please contact
local distributors or manufacturer in time, we are ready to
offer solutions for you.
- 14 -
Display/Keys
Keys
Save/
Addition/Subtration
Turn on/Measure
Sound/Mode
Turn off/Clear
Reference Point/
Unit Switch
Power Supply
Area, Volume and
Pythagorean Mode
Laser on
Maximum Value
Auxiliary Display
Record
Minimum Value
Major Display
Display
Length Mode
- 15 -
Discharge the battery door on the back of device,
and place battery according to correct polarity, then
cover the battery door.
Only 1.5 V AAA alkaline battery is applied to the
meter.
If not used for a long time, please take out the
battery to avoid battery corrosion to meter body.
Battery Installation and Replacement
Turn On/Off the Instrument
Start the Instrument/Menu Setting
Under off status, press button , device and laser
get starting simultaneously and stand by for
measurement.
Under on status, long press button for 3 seconds
to turn the device off. The device can also be shut off
without any operation for 150 seconds.
Batteries Installation
- 16 -
Unit Setting
Changing Reference Point
Units:
Short press to change the reference point.
The default reference point is the terminal baseline.
Long press button , reset current measurement
unit, the default unit is: 0.000m. There are 6 units for
selection.
Length Area Volume
1
6
5
4
3
2
0.000 m
0.00 ft
0'00\" 1/16
0 1/16 in
0.0 in
0.00 m
0.000 m2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 ft2
0.00 m2
0.000 m3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 ft3
0.00 m3
Backlight on/off
The backlight is set to turn on and off automatically.
The backlight will be on for 15 seconds if any key is
pressed. The backlight will automatically turn off if
there is no operation within 15 seconds to save
power.
Keys Sound
Long press to turn on or off the sound.
- 17 -
Self-Calibration
In order to ensure the accuracy of the device,
self-calibration function is provided.
Calibration method: In the shutdown state, hold down
, then press to power on. Release until the
screen displays flashy number at the lower end of ,
then the device enters the self-calibration mode.
Then user can adjust the value with according
to the accuracy of the device.
Adjusting range: -9 to 9mm.
Single Distance Measurement
If the measured value is 3.778m, 2mm smaller than
the actual value, the calibration value can be adjusted
up by 2mm on the existing basis with through the
calibration function.
For example, the actual distance is 3.780m.
If the measured value is 3.783m, 3mm higher than the
actual value, the calibration value can be lowered by
3mm on the existing basis with through the
calibration function.
After the adjustment, press to save the calibration
result.
Turn on the laser beam by short press of the button
under measuring mode, press the button again for
single measurement of length, then the measured
results displayed in the major display area.
- 18 -
The current measurement value will display in the
main display area. Short press or to exit the
continuous measurement mode.
Under the test mode, long press to enter the
continuous measurement mode, and the maximum
and minimum measured values measured in the
continuous measurement process will display in the
auxiliary display area.
Continuous Measurement
Area Measurement
Press once for length;
Press again for width;
Press , shows at the screen. One of the side
of rectangle blinks at the display, please follow the
below instructions for area measurement:
The device automatically calculates the area and
shows the result in the major display area. The
measuring results of the length and width of the
rectangle will be showed in the auxiliary display area.
In the measurement process, user can also press
to clear the measurement result and measure again.
Press twice to exit the area measurement state
and enter the length measurement mode.
- 19 -
Volume Measurement
Press twice, shows on the screen. One of the
side of cube blinking on the display. Follow the prompts
to complete the following:
Pythagorean Measurement
The instrument automatically performs volume calculations and the results are displayed in the main display
area. The auxiliary display area displays measurements
of the length, width and height of the cube.
Press to measure the first side (length);
Press to measure the second side (width);
Press to measure the third side (height);
In the measurement process, user can also press
to clear the measurement result and measure again.
Press twice to exit the volume measurement state
and enter the length measurement mode.
- 20 -
There are four modes of measuring the triangular
unilateral distance by means of Pythagorean theorem,
which are convenient for users to measure indirectly in
specific complex environments.
Short press three times, shows on the
screen, and the hypotenuse of the triangle flashes
Press , measure the length of hypotenuse (a)
Press , measure the length of one leg (b)
Calculate the second leg by measuring the
hypotenuse and another leg.
Calculate the hypotenuse by measuring the length
of two legs.
Short press four times, shows on the screen,
the right side of the triangle flashes
Press , measure the length of one leg (a)
Press , measure the length of another leg (b)
The device automatically calculates the length of
hypotenuse (x)
Calculate the auxiliary height by measuring the
length of the two hypotenuses and base.
Short press five times, shows on the screen,
the hypotenuse of the triangle flashes
Press , measure the length of one side (a)
Press , measure the length of the median line (b)
Press , measure the length of another side (c)
The device automatically calculates the length of
another leg (x)
The device calculates the length of the leg in full line
(x)
- 21 -
Calculate the sum of the bases by measuring the
length of the two hypotenuses and the height.
Short press six times, shows on the screen,
the hypotenuse of the triangle flashes
Press , measure the length of one hypotenuse (a)
Press , measure the length of one leg (b)
Press , measure the length of another
hypotenuse (c)
The device calculates the length of the leg in full line
(x)
In the Pythagorean Measurement Mode, the right Angle
side must be less than the hypotenuse length of the
instrument to calculate, otherwise the instrument will
display an error signal prompt. In the Pythagorean
Measurement Mode, to ensure the accuracy of the
measurement, it is necessary to ensure that the
measurement is taken from the same starting point and
in the order of the hypotenuse and right Angle side
measurements.
- 22 -
Addition/Subtraction Measurement
Single distance measurement can be added or
subtracted by adding/subtracting operations.
After measuring a single distance, the user can press
to enter the cumulative addition/subtraction.
Press , when \"+\" appears on the screen, the user
enters the cumulative addition measurement mode and
the screen displays the summation value of the last
measurement value and the current measurement
value.
Press again. When \"-\" appears on the screen, the
system enters the cumulative subtraction measurement
mode. The screen displays the difference between the
last measurement and the current measurement.
Cumulative addition/subtraction modes are selected
by .
1. Measure the first area as shown in PIC1.
2. Short press , and enter the cumulative addition
mode, then measure the second area as shown in
PIC2,
3. Short press to get the summation result of these
two areas which is showing in PIC3.
Area cumulative function:
Not only distance can be calculated in addition and
subtraction, but area and volume can do the calculation
as well. Take area as sample:
- 23 -
Record Function
PIC1 PIC2 PIC3
After the area accumulation step 2 operation, continue
the measurement, you can add the next area again,
repeat this step, you can do multiple accumulations,
and finally perform the sum step 3.
Multiple Area Addition:
Repeat to press to switch the addition/subtraction
mode. The cumulative subtraction and multiple
cumulative subtraction operations are similar to
cumulative addition operations. For details, see
Cumulative Operations.
Multiple Area Subtraction:
In measurement mode, the current data is valid, the
instrument will automatically store, and the record
number“ ”at the top of the screen will continue to
accumulate.
- 24 -
Read/Delete the Record:
Signal is too weak
Out of the
measurement range
Use the device within the
measurement range.
Choose the surface with stronger
reflection. Use the reflecting plate.
Signal is too strong Choose the surface with weaker
reflection.
Low battery voltage Replace batteries.
Beyond working
temperature
Pythagoras measuring
breaks the rules
Re-measure and ensure that
hypotenuse is longer than legs.
Use the device in the specified
temperature.
Long press to browse the stored measurement
data, use to scroll backward for record, use to
scroll forward for record. While browsing records, long
press to clear all records. Short press or to
exit the mode.
Error Information
Prompt
Err
Err 1
Err 2
Err 3
Err 4
Err 5
Cause Cause
During use, the following prompts may be displayed in
the major display area:
- 25 -
Technology Specifications
±(2mm+dx1/10000)
Indoor standard reflective surfaces **
20s (Single measurement)
99 units
630-670nm, <1mW
SW-M70S SW-M100S SW-M120S
0.05-70m 0.05-105m 0.05-125m
ITEM
Measuring Range
Measuring Accuracy
Continuous
Measurement Function
Max Storage
Min/Max Value
Self-Calibration
Buttons/Keys Sound
Laser Level
Laser Type
Area and Volume
Measurement Function
Automatically Cut
off Laser
Pythagorean
Measurement Function
Add and Subtract
Measurement Function
Area/Volume Addition
Subtraction
Working Temperature 0°C~40°C
Storage Temperature -20°C-60°C
Storage Humidity 20%-80%RH
Dimension 100x43x23mm
Automatic Shutdown 150s
Battery 2x1.5V AAA
Operating Time ≥8000 times (Single measurement)
Class II
- 26 -
Instrument Maintenance
* \"d\" indicates the actual distance.
** Under adverse environmental conditions, such as
excessive sunlight, large fluctuations in ambient
temperature, weak reflectivity of the reflective surface,
or insufficient battery power, measurement results may
exhibit significant errors. In such cases, using a target
reflector can improve measurement accuracy.
Do not store the instrument in a high temperature
and humidity environment for a long time. If the instrument is not used for a long time, please put it in the
pouch and store it in a cool and dry place.
Please keep the device surface clean. Use a soft wet
cloth to wipe the dust on the surface. Do not use
corrosive liquid to clean the device. The laser window
and focusing lens can be wiped in the same way as
the optical device surface.
- 27 -
Packing List
Please check if the accessories are completed
according to the below list.
No.
1 1
1
1
1
Item
Meter
Unit
pc
pc
pc
pc
QTY Note
2 1.5V AAA Battery pc 2
3
4
5
Hand Strap
User Manual
Gift Box
- 28 -
深達威科技（廣東）股份有限公司
地址：廣東省東莞市虎門鎮虎門團結路58號
Sndway Technology (Guangdong) Co., Ltd.
Add: No.58, Humen Tuanjie Road, Humen Town
Dongguan City, Guangdong Province, China
全國咨詢服務熱線 /Service Hotline: 400-125-6969
電話/Tel: 0769-85265688
網址/Web: www.sndway.com
郵箱/E-mail: market@sndway.com
